Da li je neko uspeo ovo? [MDPC-X alat]

[gagi75]

ko sto rece iz naslova jel neko uspeo ovo da uradi i nakraju da zabije deo sebi u palac.....

 

[gordan84]

Nije.

 

[JBL]

Ako si slomio mdpc-x alat onda bi one ostale slomio na prvom pinu

 

[Don Workinson]

Cek lazes da je ovo "original" mdpc alat? Pa sta si mu radio?!

 

[gagi75]

jeste vala original posteno ga platio gurno ga u 24 pinski molex
2.malo gurno unutra
3.povukao zicu unazad da izvadim
4posto nije islo izvadim taj alat
5 gurnem ponovo ovaj put maalo jace gurnem i eto zla nisam pazio na palac
6.najveci i najgori i najjjjjjjjjj naj sex je sto je to bila poslednja zica koja je rebala izici hahhahahahahah
bem ti k...srecu

 

[gagi75]

elem nadjoh ovaj drugi alat sta mislite da li je bolji od prethodnog i moze li mi neko nabaviti za testiranje.....
ali ozbiljno
s:0

 

[illidan]

ovo ce ti puci pre MDPC-X

 

[gagi75]

znaci bato da se vrnem na spajalice i heftalice.....

 

[illidan]

najjeftinije

 

[gagi75]

ili da uzmem ponovo istu tu budzu tj alat pa da probam ponovo

 

[illidan]

moras biti pazljiviji, nije ti to motor

 

[Godzilla]

A sa tim jos treba biti pazljiviji.

 

[gagi75]

aaaaa motor je drugo nemoj tako nisko hehe stigla guma da montiram eto mene u ns sa napajanjem i punim bisagama heftalica i municije od spajalica kod tebe....

 

[JBL]

Verovatno si ga savio malo jace dok je bio unutra jbg RIP mdpc-x alat

 

[gagi75]

ma jok bre gurao ravno samo a kako se desilo pojma nemam uopste nisam krivio jer nisam smeo koliko sam shvatio samo ravno
a bem ga kako je skliznuo moram probati da ga napravim...ili kupiti drugi
e al mi ostade onaj okrugli to sam dooktorirao i od kulera.... zezaju me samo ovi cetvrtasti....
bem ga nisam nikad gurao u cetvrtastu rupu....

 

[illidan]

aaaaa motor je drugo nemoj tako nisko hehe stigla guma da montiram eto mene u ns sa napajanjem i punim bisagama heftalica i municije od spajalica kod tebe....

salim se

 

[gagi75]

ma opusteno bre palac me boli kako cu sutra na posao da radim pojma nemam
nisam dobio nikakav tutorial za guranje alata.......hehehehe

 

[Steamroller]

Ja tu napraviti sebi nešto u podrumu kad dođe red na "slivnike"

 

[voodoons]

a gde je slika palca?

 

[animaN]

a gde je slika palca?

+1 or didn't happen

 

[c-p-r]

LC Power PSU?

 

[MegaSkot]

Naručih ti drugi alat.

p.s. nemaju titanijumski

 

[illidan]

recicu Nilsu da napravi

 

[MegaSkot]

Mail od Nilsa:

The package is on the way. I hope you didn't destroy your first MOLEX! If you did ... grrrrrr ... nobody is allowed to kill a holy MOLEX!

Be careful with the MOLEX pin remover, because it's a tool for fine work! If you use it right, it will be the tool for your lifetime. Especially at the beginning the risk of damage is high, when you don't have the right technique - start carefully.
Usage: First you can prepare the pins a little bit in order to loosen them. Push and pull on the cable close to the pin while doing a circular motion. Then you put the connector horizontally on the table and insert the tips of the MOLEX horizontally to the connector. The tips need to be on the outside of the pin in order to press on the little hooks on the outside of the pin. Push the tips as far in as it goes. You are at the maximum just before the tips get wider. Now it's important that you develop a holding technique that enables you to do the following with one hand: Holding the connector AND keeping the pin-Remover in "deep inside" position (but with no force on the MOLEX!). Your other hand is needed just for pulling the cable.
The force-vector (related to the pin itself) needs to be absolutely straight - extremely important! In order to create enough pulling force, you can wind the cable around your finger. But remember that the force "at the pin" needs to be 100% straight. Otherwise the (not to be underestimated) force can result in a seperation of pin and cable. If you have pins, which don’t come out and you are 100% sure that your technique is as correct as described, you can really try to pull harder, because it might be more force needed than you think – but never ever force on the MOLEX itself! (There might be a solution if nothing comes out, even with perfect technique: While the MOLEX is inserted, you can rotate it over the length-axis just a tiny little bit. Be extremely careful when you do it and only do it when you totally understand the other techniques. This slight rotation might break the Pin-Remover if you do too much. Only do this as a last solution.)
Experience will make you a master. Every pin can be removed, but you need to learn the technique!

Nils

 

[gagi75]

narode bolje radi sa jednom nozicom nego sa dve demonstriracu vam nego nastavak sledi......
poenta je sto cackas mecku.......moze da se upali alarm
i ode u pm da li se nekom desilo ovo 2 deo
samo napajanje crklo